Why you can trust Tom's Hardware Our expert reviewers spend hours testing and comparing products and services so you can choose the best for you. Find out more about how we test.
Advanced Transient Response Tests
For details about our transient response testing, please click here.
In the real world, power supplies are always working with loads that change. It's of immense importance, then, for the PSU to keep its rails within the ATX specification's defined ranges. The smaller the deviations, the more stable your PC will be with less stress applied to its components.
We should note that the ATX spec requires capacitive loading during the transient rests, but in our methodology, we also choose to apply a worst case scenario with no additional capacitance on the rails.
Advanced Transient Response at 20% – 20ms
| Voltage | Before | After | Change | Pass/Fail |
| 12V | 12.096V | 11.945V | 1.25% | Pass |
| 5V | 5.042V | 4.941V | 2.00% | Pass |
| 3.3V | 3.332V | 3.175V | 4.71% | Pass |
| 5VSB | 5.084V | 5.029V | 1.08% | Pass |
Advanced Transient Response at 20% – 10ms
| Voltage | Before | After | Change | Pass/Fail |
| 12V | 12.097V | 11.947V | 1.23% | Pass |
| 5V | 5.042V | 4.941V | 2.00% | Pass |
| 3.3V | 3.332V | 3.175V | 4.72% | Pass |
| 5VSB | 5.084V | 5.036V | 0.94% | Pass |
Advanced Transient Response at 20% – 1ms
| Voltage | Before | After | Change | Pass/Fail |
| 12V | 12.097V | 11.957V | 1.16% | Pass |
| 5V | 5.042V | 4.942V | 1.98% | Pass |
| 3.3V | 3.331V | 3.173V | 4.74% | Pass |
| 5VSB | 5.084V | 5.038V | 0.90% | Pass |
Advanced Transient Response at 50% – 20ms
| Voltage | Before | After | Change | Pass/Fail |
| 12V | 12.097V | 11.949V | 1.23% | Pass |
| 5V | 5.039V | 4.939V | 1.98% | Pass |
| 3.3V | 3.330V | 3.167V | 4.89% | Pass |
| 5VSB | 5.049V | 4.995V | 1.06% | Pass |
Advanced Transient Response at 50% – 10ms
| Voltage | Before | After | Change | Pass/Fail |
| 12V | 12.098V | 11.952V | 1.21% | Pass |
| 5V | 5.039V | 4.940V | 1.96% | Pass |
| 3.3V | 3.330V | 3.168V | 4.88% | Pass |
| 5VSB | 5.049V | 4.998V | 1.02% | Pass |
Advanced Transient Response at 50% – 1ms
| Voltage | Before | After | Change | Pass/Fail |
| 12V | 12.098V | 11.962V | 1.13% | Pass |
| 5V | 5.040V | 4.941V | 1.97% | Pass |
| 3.3V | 3.330V | 3.164V | 4.98% | Pass |
| 5VSB | 5.049V | 5.000V | 0.98% | Pass |
Transient response is good enough at 12V and 5VSB, decent at 5V and mediocre at 3.3V.
Turn-On Transient Tests
In the next set of tests, we measure the PSU's response in simpler transient load scenarios—during its power-on phase. Ideally, we don't want to see any voltage overshoots or spikes since those put a lot of stress on the DC-DC converters of installed components.
There is a tiny voltage overshoot at 5VSB, while at 12V, we meet the usual steps and some rigging in the last test, where we apply a full load immediately after switching on the PSU.
Power Supply Timing Tests
There are several signals generated by the power supply, which need to be within specified, by the ATX spec, ranges. If they are not, there can be compatibility issues with other system parts, especially mainboards. From year 2020, the PSU's Power-on time (T1) has to be lower than 150ms and the PWR_OK delay (T3) from 100 to 150ms, to be compatible with the Alternative Sleep Mode.
| T1 (Power-on time) & T3 (PWR_OK delay) | ||
|---|---|---|
| Load | T1 | T3 |
| 20% | 90ms | 316ms |
| 100% | 94ms | 318ms |
The PWR_OK delay is way above the 100-150ms region, so the PSU does not support the alternative sleep mode recommended by the ATX spec. The power-on time is below 100ms, at least, but it could be close to 50ms, to not create compatibility issues with "picky" mainboards.
Ripple Measurements
Ripple represents the AC fluctuations (periodic) and noise (random) found in the PSU's DC rails. This phenomenon significantly decreases the capacitors' lifespan because it causes them to run hotter. A 10-degree Celsius increase can cut into a cap's useful life by 50%. Ripple also plays an important role in overall system stability, especially when overclocking is involved.
The ripple limits, according to the ATX specification, are 120mV (+12V) and 50mV (5V, 3.3V, and 5VSB).
| Test | 12V | 5V | 3.3V | 5VSB | Pass/Fail |
| 10% Load | 11.8 mV | 11.9 mV | 14.4 mV | 5.8 mV | Pass |
| 20% Load | 13.9 mV | 13.7 mV | 16.5 mV | 6.1 mV | Pass |
| 30% Load | 15.5 mV | 12.5 mV | 16.1 mV | 6.4 mV | Pass |
| 40% Load | 15.6 mV | 12.4 mV | 16.4 mV | 6.8 mV | Pass |
| 50% Load | 16.2 mV | 13.3 mV | 15.8 mV | 6.7 mV | Pass |
| 60% Load | 16.8 mV | 13.3 mV | 16.6 mV | 7.7 mV | Pass |
| 70% Load | 18.4 mV | 13.0 mV | 16.6 mV | 6.8 mV | Pass |
| 80% Load | 18.9 mV | 14.4 mV | 17.2 mV | 8.0 mV | Pass |
| 90% Load | 21.4 mV | 15.2 mV | 18.3 mV | 9.6 mV | Pass |
| 100% Load | 33.7 mV | 16.3 mV | 20.1 mV | 11.2 mV | Pass |
| 110% Load | 37.5 mV | 18.4 mV | 21.7 mV | 10.6 mV | Pass |
| Crossload 1 | 18.6 mV | 14.6 mV | 17.6 mV | 6.5 mV | Pass |
| Crossload 2 | 14.2 mV | 14.7 mV | 15.8 mV | 6.0 mV | Pass |
| Crossload 3 | 11.9 mV | 11.6 mV | 14.7 mV | 5.5 mV | Pass |
| Crossload 4 | 33.3 mV | 13.1 mV | 16.7 mV | 8.2 mV | Pass |
There is a significant increase in the 12V rail's ripple from 90% to full load, which doesn't look nice on the charts. Still, you cannot call ripple suppression bad since 33.7mV at 12V under sky-high operating temperatures is not that high.
Ripple At Full Load
Ripple At 110% Load
Ripple At Cross-Load 1
Ripple At Cross-Load 4
EMC Pre-Compliance Testing – Average & Quasi-Peak EMI Detector Results
Electromagnetic Compatibility (EMC) is the ability of a device to operate properly in its environment without disrupting the proper operation of other nearby devices.
Electromagnetic Interference (EMI) stands for the electromagnetic energy a device emits, and it can cause problems in other nearby devices if too high. For example, it can cause increased static noise in your headphones or/and speakers.
΅We use TekBox's EMCview to conduct our EMC pre-compliance testing.
Conducted EMI emissions are low.
MORE: Best Power Supplies
MORE: How We Test Power Supplies
MORE: All Power Supply Content
