Antec Aria AR300 PSU Repair

Features
By Daniel Sauvageau
last updated

Have you ever bought a computer case with a proprietary PSU form factor? What do you do when it eventually wears out? One option is to repair it.

Where To Go From Now

Now that the out-of-bounds 5VSB output is reined in, we still have the power-up failure issue to fix. Time to revisit that EC4 capacitor.

I hooked up my multimeter to measure voltage across EC4's leads again, plugged the power supply in, turned it on and still got 0V. Something must have blown somewhere between the auxiliary transformer winding, the capacitor, its rectifier diode and whatever else is left. Time for some more reverse-engineering.

Remember when I said the AUX2 output seemed oddly convoluted? Now this is a classic flyback output: an output winding with one of its ends connected directly to the output side's reference point, the other end connected to a rectifier diode, an output filter capacitor and a zener diode across the capacitor to limit the maximum voltage across it. ZD4 is that scorching-hot 18V zener mentioned earlier and R29 must be a current-limiting resistor for ZD4 and, by extension, EC4.

Why is R29's value unknown?

Because its markings are partially burnt off and what remains of them does not seem to make sense based on the previous schematic. Read one way, it it seems to be 5?6, and read in the opposite direction, it would be 9?5. On my multimeter, the resistor reads open, and a value over 100MΩ would not make any sense. A blown resistor in series with the transformer winding would definitely explain why the main outputs still refuse to turn on after changing most of the caps: no current through that resistor means no charge going into EC4 and no power for the APFC and PWM chips.

What do you think the burnt character is supposed to be? The value needs to be sufficiently low to let enough current through to power the main PWM circuit but not so low as to cause the zener diode to become searing hot. My best guess is that the missing middle character must be an R, since that would match what is left of it and 5.6Ω (5R6) makes reasonable sense for this location in the circuit. The only SMD resistors with plausibly adequate value I have in stock are 10Ω in 0805 package. Let's hope the 1208 package on the PCB was selected by ChannelWell more for its qualities as a potential jumper or excess inventory than for power dissipation. Since the 1208 resistor is glued on the PCB, I will have to solder my replacement 10Ω on top of it.

Soldering a 0805 on top of a 1208 is fairly easy: create a small solder puddle on the pads at both ends of the 1208, position your 0805 part on top of it, hold it there with either a fine-tipped tool or glue, dip your soldering iron tip in the puddle, drag it over the 1208 and 0805 terminals to create a solder bridge, repeat on the other terminal, done. If the bridge keeps breaking up, add some more solder.

Daniel Sauvageau
Daniel Sauvageau is a Contributing Writer for Tom's Hardware US. He’s known for his feature tear-downs of components and peripherals.
15 Comments Comment from the forums
  • iam2thecrowe
    That was a good read. I have a lot of custom power supplies (not PC atx) that i would like to fix at work instead of replace, would be a lot cheaper (there's some high wattage power supplies that cost $5000 to replace). Need to convince the boss to buy a good oscilloscope.
    Reply
  • Rookie_MIB
    I have several of those cases - they make nice little machines for office use but the PSUs tend to flake. I've had to replace several...
    Reply
  • Daniel Sauvageau
    All the standby power supplies I remember looking at are of the good old flyback design and one particularity of the flyback topology is that it has the worst ripple current on the output capacitors of all converter topologies or in other words: it is the harshest on output capacitors. Until I saw the waveforms while poking around the SL300, one little yet important detail skipped my mind: the harsh current waveform behavior applies to ALL outputs.

    Any flyback supply with sub-par output capacitors on any of its outputs will inevitably fail in relatively short order.

    After that 'oops' moment, I decided to pop the lid on my LG 204WT which I thought had dying CCFL tubes, popped three of its auxiliary supply capacitors off the board, measured them at 5-20 ohms of ESR, replaced them, no more flicker or random turn-on issues.
    Reply
  • gnyff
    I love it when stuff is repaired! It's so sad that almost every consumer device today is made to fail and be replaced. Even in the cases where the designer did not specifically design for failure most commonly it's definitely not cost-effective for the user to have it repaired. :-(

    Anyways, I've also replaced one of those lousy non-standard PSU. Hard to find and depressingly expensive. Thus, I am avoiding non-standard parts as much as possible now! ;-)
    By the way, in one of my systems the standby power was around 12W (!) even after shutting off 5VSB functions (wake on LAN, keyboard etc) in the BIOS. I did on bother to investigate further (thinking "lousy supply"!) and simply added a proper "full off" power switch. Probably other owners should think of doing the same ;-)
    Reply
  • Rookie_MIB
    16509494 said:
    Anyways, I've also replaced one of those lousy non-standard PSU. Hard to find and depressingly expensive. Thus, I am avoiding non-standard parts as much as possible now! ;-)
    By the way, in one of my systems the standby power was around 12W (!) even after shutting off 5VSB functions (wake on LAN, keyboard etc) in the BIOS. I did on bother to investigate further (thinking "lousy supply"!) and simply added a proper "full off" power switch. Probably other owners should think of doing the same ;-)

    I wonder if a SFX PSU could be mounted in those cases. Might be a viable solution...
    Reply
  • nukemaster
    Another great one!

    I actually was interested in that case back when it was released, but just kept rocking the Sonata and Sonata II. While my power supplies did not fail. caps leaked after a while(power supplies still worked)and I took the power supplies out of service forever.

    Rookie_MIB,
    SFX would be an interesting idea to see for sure. My SFX is still going after 5 years of 24/7 operation(not bad for a case included 300 watt unit).
    Reply
  • Daniel Sauvageau
    16509868 said:
    I wonder if a SFX PSU could be mounted in those cases. Might be a viable solution...
    The dimensions might fit but mounting holes would be on the wrong side (for mounting in a way that might fit internally) and the IEC socket would face either the motherboard or the top cover. Nothing some drill-and-tapping with some wire splicing cannot fix for people who would favor this route instead of a repair of the existing unit where that is possible.

    BTW, the total repair cost for the 5VSB side is about $1.50 for the caps and resistor. The rest is basically free since I scavenged the SCs from a dead (catastrophic primary-side failure) PSU and would have cost around $2.50 otherwise. If Asus had specified higher quality parts from Channel Well though, the PSU may have cost less than $0.50 extra to get right on the first try. Evem doing as little as specifying Teapo SC as the minimum requirement would have easily doubled the trouble-free service life over using SEK..

    It always bugs me when only a few pennies worth in parts and materials can spell the difference between a product that might only last 2-3 years and a product that should easily last 10+ years.
    Reply
  • nukemaster
    That small cost per unit adds up.

    I can not count the number of times I say, gee a xx cent part would have solved this damn issue and yet no one does it.

    Drilling and making it fit is no issue. :)

    I still get my small system fix with an SG05 case.

    Where do you get your parts from? Digikey is not too expensive, but many times the shipping cost more than the parts(especially with resistors that are cheap to begin with.).
    Reply
  • Daniel Sauvageau
    16511613 said:
    That small cost per unit adds up.

    Where do you get your parts from? Digikey is not too expensive, but many times the shipping cost more than the parts(especially with resistors that are cheap to begin with.).
    The "small cost" may add up but if you charge $1 to put the $0.50 worth of better quality parts in, you still make a 100% profit on that extra cost and you score points in the quality/reliability column. For the most part, those better quality parts are the same physical size, so no fitting or PCB layout concerns there.

    As for where I get my parts, they are mostly Digikey. I either lump my order with parts I need to repair something for someone else (and pass the shipping cost to them) or build my order for multiple non-urgent projects until it qualifies for free shipping.

    Edit: and for things like 0805 resistors and capacitors, I usually order in cut-tapes of 100 since we're still only talking $1-2 there. If I had more storage space, I would order whole reels for $10-15 (2000-3000 units) and likely never have to worry about ordering more of that resistor or capacitor value (for personal use) for the rest of my life.
    Reply
  • pjmelect
    I often repair computer power supplies and I enjoyed reading this article. One comment, that may help others and may explain some things in the article such as the power reduction of the fixed power supply.
    Capacitors with high ESR always have a very high leakage current near their rated voltage. The leakage current at low multi-meter voltage levels is not normally measurable, but increasing the voltage across the capacitor dramatically increases the leakage. Circuits with capacitors with high ESR in them normally fail not due to the ESR or the reduction of capacitance, but due to the high leakage current. If you do not have a ESR meter you can simply put a suspect capacitor across a power supply at its rated voltage and check the leakage current. A high leakage current is a good indication of a high ESR value.
    I use a in-circuit ESR meter to test all of the electrolytic capacitors (even the small ones) before I even start trying to fault find a power supply.
    Reply