PSU Roundup: Performance, Price, Efficiency

By Daniel Schuhmann
published

Efficiency

Antec’s power supply shows remarkable efficiency under full load as well as half load. It’s able to demonstrate 87.2 percent and 88 percent, respectively. Under low load, efficiency drops slightly to 83.3 percent. Just bear in mind that under full load, this is the best device in our test field.

The power supply is frugal in standby, too. It uses 690 milliwatts at zero load. At a load of 2.5 watts on the standby cable it consumes 4 watts, an efficiency of 62 percent. Antec’s voltage converter does relatively well with this result, too.

Antec Signature 650 Watt

The Antec power supply is the classic size and is thus well-suited to use in 19-inch and HTPC housings.

  • Positives
  • Negatives
  • Fan design is ideal for HTPCs.Low energy need in standbyHigher efficiencyChoice options with Molex and SATA
  • Higher price
Daniel Schuhmann
44 Comments Comment from the forums
  • falchard
    That coolermaster PSU is nice that its cables are thin since its really annoying to have those stiff cables fill a small case. However, I wonder about its interference. That insulation and mesh is there for a reason, to prevent discharge and electrical interference of other parts.

    Also I can see the reason why a person wouldn't want a CPU/ATX connector on a 700w power supply. If they had an excessively power draining system like a Quad/Tri GPU with modern high end cards it will waste alot of power and using 2 lower watt power supplies is cheaper then getting 1 high watt one.
    Reply
  • dirtmountain
    Nice fluff piece. I sure wouldn't use any of these recommendations over jonnygurus or hardwaresecrets sites though.
    Reply
  • optik
    Just bought myself Zalman's ZM-750HP with cable management and heatpipe cooling.. Cost only 131 euros.. When I saw the article's header I hoped to see it being reviewed, but no such luck. Would've been nice to see how the Zalman's offerings would've fared against others.. The productline ranges from 360Watts to full 1000Watt PSU's so plenty to choose from..
    Reply
  • Proximon
    Without voltage ripple and heat tests you can't properly evaluate a power supply. At least readers can use this as a starting point for further research.
    Reply
  • http://www.hardwaresecrets.com/article/410
    Reply
  • dirtmountain
    +1 to doctorpink
    Reply
  • chookman
    Heat is generally relative to efficiency , due the fact that the more energy lost the more heat generated.

    Ill agree with the ripple tests too, yeh great we might have a power supply that is efficient at 100% but what if the 12v rails are hovering outside of spec...? Its a nothing review really.
    Reply
  • Please add the "S" onto the word VOLT
    Thanks
    Reply
  • jt1
    falchardThat coolermaster PSU is nice that its cables are thin since its really annoying to have those stiff cables fill a small case. However, I wonder about its interference. That insulation and mesh is there for a reason, to prevent discharge and electrical interference of other parts.
    What manufacturers use insulation and mesh that block interference? The insulation on the wires of my PSUs is standard insulation, the mesh is plastic and there strictly to hold the wires in place and prevent the inside of a computer case from becoming a birds nest of wires.

    If there are manufacturers that use materials to block interferences, I'd like like to look into their products as it sounds interesting but I'd like to hear from someone actually in the know as to if it would make any difference or not.
    Reply
  • pcfxer
    Interference on a power supply is negligible. The power runs, voltages and current are of little concern for interference. IF you want to be truly theoretical it would make a "difference".

    When I studied power engineering one would need a ton of voltage or current to be 'eligible' for most electrical phenomena to occur - theoretically.
    Reply