Skip to main content

System Builder Marathon, Q1 2013: $1,600 Alternative PC

Results: Battlefield 3 And Far Cry 3

The $1,600 PC’s CrossFire configuration bumps up against Battlefield 3’s 200 FPS limit at 1680x1050 and 1920x1080. Naturally, though, you wouldn't buy this much graphics horsepower unless a single 2560x1600 display or three 1920x1080 screens were your goal. The 200 FPS limit certainly hurts the alternative system’s overall performance advantage, but a separate chart will show off its greater-than-90% gain at 5760x1080.

Cranking the detail levels up to Ultra quality, we find that just one Tahiti LE-based card isn't capable of achieving playable frame rates at 5760x1080 or, thanks to Battlefield 3’s high frame rate variability, 2560x1600.

Leaning hard on CrossFire yields playable Far Cry 3 frame rates at 5760x1080, but only at our lower test settings. Dialing up to the Ultra quality preset drops the $1,600 PC’s playability to 2560x1600, though you might be able to get similar performance at 4800x900.

The $1,000 PC is primarily limited to 1920x1080, High quality details, and no extra graphics features in this title.

  • Azn Cracker
    Aren't the 7870 myst only $240 a piece?
    Reply
  • Crashman
    Azn CrackerAren't the 7870 myst only $240 a piece?See This?
    Article TextThe prices in that table were what we paid when the parts were ordered, and a lot of them changed over the last six weeks. For example, the PowerColor card is $20 less, per board. Other prices are up. All told, then, the total cost of buying our machine and replicating the build is within $20 of our original invoice.
    Reply
  • mikenygmail
    Please call the graphics cards 7870 LE from the start, like this:
    "Video Cards: 2 x 7870 LE - PowerColor PCS+ AX7870 Myst Edition"
    After all, it is much more than a standard 7870.
    I had no idea it was the LE until I got to the third page.
    Reply
  • Crashman
    mikenygmailPlease call the graphics cards 7870 LE from the start, like this:"Video Cards: 2 x 7870 LE - PowerColor PCS+ AX7870 Myst Edition"After all, it is much more than a standard 7870.I had no idea it was the LE until I got to the third page.In AMD/ATI model lingo, LE stands for a cut-down part. So a Tahiti-LE wouldn't be a 7870 LE, it would be a 7950 LE. The fact that it carries the 7870 model number is unfortunate, but the article attempts to make it clear that this is indeed a Tahiti-LE
    Reply
  • stickmansam
    Why not the 7870XT like Sapphire calls it?
    Reply
  • Crashman
    StickmansamWhy not the 7870XT like Sapphire calls it?That's fine, please tell AMD to do the re-brand!
    Reply
  • pyro226
    "a board damaged a processor that in turn damaged every board it touched, which in turn would damage every processor it touched" and ram damaging a CPU?

    I think I'm a bit afraid to build computers now. If either of those situations would have happened to my $600 build, I would have cried and given up...
    Reply
  • I like that build better.. :D
    Reply
  • Fulgurant
    pyro226"a board damaged a processor that in turn damaged every board it touched, which in turn would damage every processor it touched" and ram damaging a CPU?I think I'm a bit afraid to build computers now. If either of those situations would have happened to my $600 build, I would have cried and given up...
    That sort of thing happens once in a blue moon. Don't let it bother you.

    I guess Tom's tale of woe summarizes why Intel recommends against higher than 1.575 volts on the memory controller of Ivy/Sandy:

    http://www.intel.com/support/processors/sb/CS-029913.htm#4
    IntelWhat are the Intel® Core™ i7 desktop processor DDR3 memory voltage limitations?Intel® recommends using memory that adheres to the Jedec memory specification for DDR3 memory which is 1.5 volts, plus or minus 5%. Anything more than this voltage can damage the processor or significantly reduce the processor life span.
    In any case, the performance benefits of overclocking memory on a Sandy/Ivy platform seem so miniscule that it's scarcely even worth considering. Buy memory capable of an appropriate speed @ 1.5V, and leave it be.

    (I know Tom mentions Intel's position on memory voltage on the last page of the article, but I wanted to re-emphasize it because I've seen literally hundreds of people dismiss Intel's statement on various hardware forums. When sites like Tom's Hardware push limits, even for questionable performance gains, we all benefit -- but when someone who's on a budget and might not know any better pushes limits on his own, hard-earned hardware, the results might be tragic. Tom's experiments with this stuff so we don't have to.)
    Reply
  • Crashman
    pyro226"a board damaged a processor that in turn damaged every board it touched, which in turn would damage every processor it touched" and ram damaging a CPU?I think I'm a bit afraid to build computers now. If either of those situations would have happened to my $600 build, I would have cried and given up...I told Chris the system was cursed, but he refused to let the project go after the seventh day. Three more days rescued the content, if not the hardware...
    FulgurantThat sort of thing happens once in a blue moon. Don't let it bother you.Once every 12 years is twice in 13 years too often...
    Reply